Start with the right part and a clean workspace
A comfortable, leak-free pump session begins before you attach anything to your body. The Willow Sync Flange Set 24mm (2-pack) is a replacement part set, so confirm you have the correct size and that all pieces are clean and dry. The supplied information does not include a step-by-step assembly diagram or a list of included components, so treat the steps below as a practical framework rather than a manufacturer's instruction sheet.
Set out a clean towel or mat, wash your hands, and inspect each flange for cracks, cloudiness, or stretched edges. The catalog guideline is to replace parts every 90 days, or sooner if you notice discomfort or signs of wear. Starting with worn parts makes fit problems harder to diagnose.
A simple installation sequence for the Willow Sync Flange Set
The exact connection points depend on your pump model and the parts you already own. Use these checkpoints to install the flange set methodically and catch fit issues early.
- Match the flange to your pump: The Willow Sync Flange Set 24mm is designed for the Willow Sync system. Check that the flange opening and connection points align with your pump's container or diaphragm assembly before pushing anything into place.
- Seat the flange firmly but gently: Press the flange into its mating part until it sits flush. Avoid twisting or forcing it; resistance usually means a misalignment, not a need for more pressure.
- Check the seal: Run a finger around the connection to feel for gaps or uneven edges. A flush, even seal helps prevent suction loss during pumping.
- Center the flange on your breast: Position the flange so your nipple sits centrally in the tunnel, not pressed against one side. Off-center placement is a common cause of discomfort and incomplete drainage.
- Test suction before you commit: Start your pump on a low setting and listen for hissing or feel for a drop in suction. If either occurs, stop and reseat the flange before continuing.
What the Willow Sync Flange Set record confirms
- Willow Sync Flange Set 24mm (2-pack): Willow Sync Flange Set 24mm (2-pack) The 24mm size is the only flange size in this record. If you need a different size, the supplied information does not confirm availability in this set.

Willow Sync Flange Set 24mm (2-pack) - Willow Sync Flange Set 24mm (2-pack): Replace every 90 days, or when you notice discomfort or signs of wear. This guideline applies to the flange set and helps you decide when fit problems are actually wear problems.
- Willow Sync Flange Set 24mm (2-pack): The set is listed in the Accessories category. It is a replacement part, not a complete pump kit, so installation assumes you already have the compatible Willow Sync pump and any other required parts.
Checking 24mm flange fit without guesswork
The supplied information does not include a fit chart, measurement instructions, or a recommended nipple-to-tunnel ratio. Use these observational checks instead of relying on numbers you do not have.
- Comfort during pumping: You should feel gentle suction, not pinching or rubbing at the base of the nipple. Discomfort that persists after repositioning is a reason to stop and reassess.
- Even draw: Milk should flow from around the nipple, not from one side only. Uneven draw can signal that the flange is off-center or the wrong size for you.
- No air leaks: A visible gap or a whistling sound at the flange connection means air is entering the system. Reseat the flange and check for cracks.
- Skin marking: Temporary light redness at the flange rim can happen, but deep indentations or soreness that lasts between sessions suggest the fit needs attention.
When installation problems are really replacement problems
If a flange that used to fit well now leaks, feels loose, or requires constant repositioning, the part may be worn rather than incorrectly installed. The catalog guideline is every 90 days, or sooner with discomfort or visible wear. A 2-pack gives you a spare so you can replace one flange and keep pumping while you inspect the other.
The supplied record does not specify cleaning temperatures, sanitizing methods, or dishwasher suitability. Follow the care instructions that came with your pump and flange set; if those are unavailable, contact Willow support rather than guessing at heat or chemical exposure that could damage the part.
Comfortable pumping flange tips that do not rely on guesswork
Small adjustments during installation often make the biggest difference to comfort. These tips stay within what the supplied evidence supports.
- Install before you put on your pumping bra: Assemble the flange set first, then position the bra around it. This reduces the chance of shifting the flange out of alignment while you adjust clothing.
- Keep spare parts within reach: A second flange in the 2-pack means you can swap immediately if you notice wear or discomfort mid-session, rather than pushing through.
- Log your replacement date: Write the date on the flange or in your phone when you first use it. The 90-day guideline is easier to follow when you can see it.


